Every time you revolve the key to the Start position on your Pontiac automobile the starter motor offers the battery and also a solenoid come spin the crankshaft to start the engine. The pinion gear on the starter and other internal materials make this feasible as well; however, these materials wear the end and, after numerous starts, utlimately fail. In ~ that suggest you have to replace the starter motor. Through the exactly replacement for your details Pontiac vehicle model, follow this overview to install the new unit.


Under The Hood:

How to readjust the Starter on a 1995 Pontiac

Lift the right front finish of the Pontiac with the floor jack, so the you can place the jack was standing under the best front frame. Reduced the Pontiac onto the jack stand. Place the wheel chocks at earlier of the rear wheels to prevent the Pontiac from rolling.

You are watching: 2003 pontiac grand am starter location


Open the hood and also use the battery wrench to disconnect the negative battery cable indigenous the battery. Press the cable finish into a position where it cannot accidentally contact the battery terminal during the fix process.

Climb underneath the right front the the Pontiac and locate the starter. Its place will be determined by the year and also model of her Pontiac, yet it have the right to be uncovered by looking at the best side of the engine, wherein the infection bell housing is bolted come the earlier of the engine block.

Disconnect the starter wiring using the socket set.

Support the human body of the starter v one hand when you remove its mounting bolts through your various other hand and the socket set. Carry out not let the starter weight come under on the bolts if you room removing them.

Compare the old starter come the instead of starter. It"s not uncommon for auto components stores to market the not correct starter. Make sure the two space physically identical prior to attempting to install the replacement unit.

Hold the replacement starter in position, making sure you totally support that weight through one hand while you thread the mounting bolts in with your various other hand. Without relieving the support, take the socket collection and tighten the mounting bolts down completely.

Reattach the starter wiring and also tighten the starter down v the socket set.

Reconnect the an unfavorable battery cable v the battery cable wrench. Reduced the Pontiac off the jack stand with the floor jack.


Items you will need

Floor jack

Jack stand

Wheel chocks

Battery wrench

Socket set

Replacement starter


How to change the Starter ~ above a 1999 Pontiac cool Am

Removal

Lift the hood top top the cool Am and locate the car’s battery. Determine the an unfavorable post ~ above the battery by its minus symbol on the optimal of the battery case. Use a socket wrench come loosen and also remove the cable native its post on the battery. Plunder the whole metal terminal in ~ the end of the battery cable with electric tape. Place the cable under within the engine compartment. Make sure the cable’s not contacting any type of other metal or the engine.

Open the driver door and totally engage the cool Am’s emergency brake. Progressive the car at its jacking suggest on the former passenger side utilizing a automobile jack. The bottom of the tire must visibly measure eight to nine inches native the ground.

Position a jack stand slightly left of the vehicle jack. Eliminate the locking pen from the support arm on the jack stand. Progressive the assistance arm to accommodate the elevation of the automobile jack. Return the locking pin to the assistance arm of the jack stand to for sure its height. Slightly lower the vehicle jack so that the jack stand have the right to bear few of the car’s weight. Carry out not eliminate the car jack. Rock the car ago and front slightly to assure it will remain stable.

Slide under the cool Am head very first and find the starter. It will certainly resemble a large elongated golden or black capsule. The solenoid will connect directly come it and also will resemble a smaller sized capsule as well.

Label every of the wires associated to the solenoid clearly with white painter"s tape. Perform not use words top top the painter"s tape such together “red or black.” Instead, brand the wires “inner and also outer” or “left and right.” usage a socket wrench to remove the wire-securing nuts and slide the wires off your mounting bolts.

Remove the bolts securing the flywheel cover v a socket wrench if you have actually the 3.4L cool Am. Lower the cover native its mounting position on the flywheel. Location the cover and its securing bolt come the next of the occupational area.

Remove the starter’s retaining bolts at its base where it mounts versus the engine. Begin with the top bolt. Before you eliminate the reduced starter bolt, assistance the starter with your totally free hand. Remove the bolt and place both hand on the starter as you reduced it far from the mounting position.

Installation

Place the starter ago into its original mounting position precisely as you gotten rid of the old starter. Support the starter and also hand thread each of the starter’s retaining bolts. This will assure the starter lines up correctly. Collection your 3/8-inch-drive speak wrench to 30 ft-lbs. Fully secure the bottom starter retaining bolt followed by the top bolt.

Place the solenoid’s wires ago onto their correct mounting point. Start both of the solenoid wires retaining nuts by hand. Reset the 3/8-inch-drive speak wrench come 22 ft-lbs. And fully secure both retaining nuts. Remove the painter"s tape from the solenoid’s wires. If you eliminated the flywheel cover, mount it back into its original position. Hand thread each of the cover’s retaining bolts. Collection your 1/4-inch-drive speak wrench to 89 inch-pounds. Fully secure the flywheel cover’s retaining bolts one in ~ a time.

Remove every one of the tools you provided while under the car. Raise the automobile jack slightly to relieve the car’s weight on the jack stand. On slide the jack stand from in ~ the grand Am. Reduced the car completely to the ground and remove the automobile jack.

Remove the electrical tape from the an unfavorable battery cable terminal. Securely reconnect the cable back to its post on the battery through a socket wrench. Closeup of the door the hood and also release the car’s emergency brake. Begin the engine come test out the brand-new starter.


Items you will certainly need

Socket-wrench set

Black electrical tape

Car jack

Jack stand

White painter"s tape

3/8-inch journey torque wrench

1/4-inch journey torque wrench


How to change the Starter ~ above a "97 grand Am

Identify the starter"s location on the engine. On 1997 Pontiac grand Am, the starter is uncovered underneath the entry manifold and above the oil filter. The starter is the part that is about half the dimension of a football and also looks choose two cylindrical piece joined together (one cylinder is bigger than the other).

Raise the cool Am by control it increase on ramps. If it will certainly not start, then you will should raise it by utilizing a floor jack and also jack stands. Location the floor jack ~ above the driver"s side and raise it, place the jack under the frame. Release the floor jack and do the same process on the passenger side of the car.

Remove the oil filter from under the engine. In bespeak to change the starter ~ above a 1997 Pontiac grand Am, you will must remove the oil filter in order to accessibility the bolts hold the starter right into place. Put the oil filter face down on peak of a drain pan so the excess oil can drainpipe from it while you room replacing the starter.

Disconnect the black battery cable native your auto battery. This will ensure the you will certainly not it is in electrocuted while working on your car"s electric system, part of which leads to the starter. Wait because that fifteen minute so that any potential electrical charges deserve to dissipate.

Change your oil when you space waiting. Since you need to remove the oil filter, you can as well readjust the oil and put a new filter on after transforming your starter. Be certain that you room not enabling any oil come leak on your driveway.

Disconnect the electrical link tab that is leading to your starter ~ above your cool Am. If it is stuck, climate gently pry it through a flat-head screwdriver.

Unscrew the copper nut holding the electric wires right into place in prior of the starter. This will offer you an ext room to job-related with as you remove your starter from the engine.

Unscrew the 2 bolts stop the starter to the flywheel of her engine. Remove the bolts and then eliminate the starter.

Slide the new starter into place and bolt in the stop bolts come secure it come the flywheel. If you room cranking on the bolts in bespeak to gain them into place, climate you may not have ideal alignment in between the starter and the flywheel. If this is the case, then you will need to remove it and slide it ago into place.

Connect the electrical link tab resulting in the starter. Placed the oil filter back on. Reconnect the negative battery terminal with the black color cable. Try beginning your Pontiac cool Am.

Lower her 1997 Pontiac cool Am indigenous the ramps or jack stands once you have efficiently replaced your starter.


Items you will need

Socket wrench with adapters

Replacement starter

Mechanic"s gloves

Car ramps

Jack stands

Floor jack

Oil filter

Motor oil

Oil catch pan

Oil filter wrench


How to replace the Starter on a Pontiac Sunbird

Remove the Starter

Remove the an unfavorable battery cable utilizing a wrench.

Take the engine harness off the engine mount come gain access to the starter mounting bolts utilizing a ratchet and also socket, if necessary.

Raise the prior of your Pontiac Sunbird making use of a floor jack and also support that on two jack stands. On some Sunbird models, you might have accessibility to the top starter-mounting bolt from the height of the engine compartment.

Unbolt the solenoid cover indigenous the height of the starter motor, if your particular model is equipped with it. Usage a ratchet and also socket.

Label the wires associated to the starter solenoid, placed on optimal of the starter motor, if necessary. Then remove the wires and the battery cable indigenous the solenoid utilizing a wrench or ratchet and socket.

Detach the rear assistance bracket native the starter motor making use of a ratchet, ratchet extension and also socket.

Unscrew the two starter-to-engine bolts using a ratchet, ratchet extension and socket. Relying on your details Sunbird model, these starter-mounting bolts may be various in size and there can be one or more shims an installed between the starter and also engine block. Make a note of these items to do starter installation easier, if necessary.

Remove the starter from the vehicle.

Install the new Starter

Set the starter motor and shims in place.

Start the two starter-to-engine mounting bolts through hand or usage the ratchet extension. Climate tighten the bolts using the ratchet, ratchet extension and socket.

Attach the rear assistance bracket indigenous the starter motor making use of the ratchet, ratchet extension and socket.

Connect the wires and also battery cable come the starter solenoid using the wrench or ratchet and socket.

Install the solenoid cover to the optimal of the starter motor, if your details model is equipped through it. Usage the ratchet and also socket.

Lower the vehicle.

Attach the engine exploit to the engine mount using the ratchet and socket, if you had actually to eliminate it to gain accessibility to the starter mounting bolts.

Connect the negative battery cable using the wrench.

Update the ECM/PCM Memory

Perform an "Idle Learn" procedure on her Pontiac Sunbird if that is equipped v a 3.0L engine. See the tip box in ~ the bottom of this article for an ext information.

Hook up a perfect scan device to the Data link Connector (DLC) located under the dashboard.

Turn the ignition switch to the on position but do not begin the engine.

Select the Idle waiting Controller (IAC) top top the scan tool; walk to assorted Test Mode and also select Idle Learn.

Make certain the transmission is in Park (automatic) or Neutral (manual).

Run the test adhering to the indict on the scan tool.

See more: Most Of The Mass Of An Atom Is Concentrated In The, Where Is The Mass Of The Atom Concentrated

Unplug the scan tool and also turn turn off the ignition switch when you have actually finished the test.