Jimmi" Jammer® residence Where come buy every our commodities

If you have come across this web page while browsing door dashboard removal for your F150, please take a minute to inspect out the Jimmi" Jammer® for your truck. If you are going to it is in inside your door, currently is the moment to download this simple yet efficient security product.

This accuse will present you how to install a Jimmi" Jammer® ~ above the following vehicles:

Full size Ford F-150 based truck, 2004 - 14, consisting of Raptor models. Vehicle drivers front door is shown, passenger side and also rear doors are similar. Note: This Jimmi" Jammer® accuse does not cover 2015 and newer F150.

Jimmi" Jammer® component Numbers: (Each kit comes with 2 plates unless otherwise noted.) Get PN 113400 if you have actually keyless entry, and no lock ~ above the passenger door handle. get PN 113450 if you execute not have keyless entry, and also have a lock cylinder on each front door handle. Get PN 113451 if you perform not have keyless entry, and have a lock cylinder only on the drivers side door handle. (No lock on pass door handle.)Note: Each door must be protected by a bowl whether over there is a lock on the take care of or not. Over there are various other rods within the door that have the right to be accessed if no key is current to protect them.

You are watching: How to remove door panel on 2004 f150

Get PN 113470 for your rear doors top top a 4 door truck. Get PN 113475 for your tailgate handle. (Yes, the thieves favor to strike these too, either to steal the tailgate or to get in the back if you have actually a shell on the van bed.) see product details because that the tailgate manage Jimmi" Jammer® here or see and also installation tutorial for the tailgate handle Jimmi" Jammer® HERE.

We now additionally offer a Hood Latch Jimmi" Jammer®. It is possible to go through the grill and release the hood through a screwdriver. When this is done, alarms can easily be disabled, batteries steal etc. Our Hood Latch Jimmi" Jammer® will deny accessibility via the hood. Check out PN 5471.

Time Required: First door up to 45 min, 2nd door around 25 min, depending on your experience.

Tools Required:

Metric socket set with extension Long nose pliers Standard and phillips screwdrivers

Installation Procedure: (Special thanks to Marcos in Chandler, AZ for use of his truck for this tutorial!)

Back to residence page (all products). Back to Jimmi" Jammer® home. Earlier to Installation and also Support page. Come Model selection page.

Notes:

This tutorial was done top top a 2005 Ford F150. Some style changes to be made the make door dashboard removal simpler for 2009-14 trucks. Below is a good video that will present the process on 2009-2014 F150 trucks. Once you have actually the dashboard off, refer earlier to this tutorial to complete installing the Jimmi" Jammer®.

Every initiative is made to accurately portray the surroundings process. However, sometimes the vehicle manufacturer makes transforms that impact the measures in door dashboard removal or installation our product. Use this tutorial together a overview only. If you are not specific of your ability, to express installation come a professional.

Jimmi" Jammer® installation procedure Photo 1

The an initial photo mirrors a drivers side door that has the keyless entrance pad. This accuse is because that trucks with or there is no the keyless entry option. This is the vehicle drivers side or left handle. Trucks without the keyless entry will usage this same tutorial.

Work carefully and also take notes or do sketches to assist you placed the door back together properly.

Note: We now recommend removing the lock cylinder from the take care of completely. This is the only method to avoid thieves native forcing something into the lock body and bending every the tabs within the lock to gain entry. Making use of the PunchPlug™ through the Jimmi" Jammer® will aid prevent the most popular methods of entry on your truck! Details

*
1

Photo 2

Remove the 2 screws stop the inside door take care of shroud in place.

On part models, there may be a tiny plastic cover behind the door manage pull lever. Look for a seam in the plastic. Generally, this snap out yet be careful. Usage a small flat blade screwdriver to pry the little cover out of the manage recess. See small photo below.

*

*
2

Photo 3

Remove the speak grill. It need to be organized in with number of snap clips. Pull directly out very closely to remove the grill.

Look for a door panel holding screw in the upper left area behind the grill.

*
3

Photo 4a and also 4b (This action not vital on 2009 and newer trucks) see a video clip for 2009 - 14 van here.

Remove the 4 screws hold the speak in place. Pull out the speaker and disconnect the wires.

Behind the speaker room four expansions that the screws go into. The bottom two will have to be eliminated to get the door panel past them as you background the panel off later. Very closely pry the bottom two expansions out. These are reasonably brittle, so occupational carefully. Photograph 4b reflects use the a curve nosed pliers to traction the spacer off.

There is also a door dashboard holding screw behind the speaker. Remove it now.

Now is also a good time to remove the 2 screws along the bottom edge of the door panel. (Not shown.)

*
4a

*
4b

Photo 5

carefully pry the switch dashboard up. It is held in ar with numerous snap clips. Work approximately the political parties gently prying upward until the panel comes off.

This is a great time to roll the home window down, before disconnecting the move pad. This helps when removing the door panel.

(Later, ~ removing the door panel, girlfriend will need to reconnect the switches to roll the home window back increase in order to gain accessibility to the backside that the external door handle.)

*
5

Photo 6

Another door dashboard holding screw is concealed inside the cavity. Eliminate it now. Disconnect the switch pad if not already done.

You are currently ready to lift the panel turn off the door. Slide the panel upward until it is loosened from the door. (Not shown.)

Next, disconnect the cable to the within door handle. Note how it is attached therefore you have the right to put it back on effectively later. (Not shown.)

*
6

Photo 7

With the door panel turn off the door, reconnect the home window switch to role the home window back increase if it was put down earlier. You can leave the switches associated since the window may need to come down to put the door panel earlier on.

Next, very closely peel ago the plastic splash guard enough so you can reach right into the door cavity through the big opening shown. Start in one spot and peel ago slowly, make the efforts to leave the adhesive on the door.

*
7

Photo 8

Photo 8 mirrors the backside that the chauffeurs door manage from inside the door.

The yellow circle surrounds the finish of the lock pawl. The end of the lock stick is also inside the circle. Eliminate the lock rod indigenous the lock pawl in ~ this end.

A cheat to remove the rod from the pawl is to use a stubby screwdriver through a obelisk diameter a little larger than the lock pole diameter. Push the column of the screwdriver into the open finish of the lock pawl till it touch the lock rod. Wrap your finger about the lock rod and pull the rod towards the open end of the lock pawl. This will certainly release the rod native the pawl.

Note: We now recommend removing the lock cylinder indigenous the manage completely. This is the only method to avoid thieves from forcing something into the lock body and bending all the tabs within the lock to get entry. Making use of the PunchPlug™ v the Jimmi" Jammer® will aid prevent the most well-known methods of entrance on your truck! Details

*
8

Photo 9

Inside the door, remove the seed on the reduced handle stud ~ above the opposite end of the handle from the lock cylinder, presented here close to the center of picture 9.

*
9

Photo 10

Photo 10 reflects the lock pawl with the lock rod disconnected native it. Usage the an essential in the lock to revolve the lock pawl therefore the open finish points downward together shown.

This will assist ease placement of the plate.

*
10

Photo 11

The key should have a screw in the finish near the big hole. Leave the screw in the plate when the bowl is installed as that is challenging to placed it in later.

Put the plate in ar by an initial guiding the lock pawl through the huge hole in the plate. You may need to move the lock pawl v the an essential to obtain the plate on properly. As soon as the key is in location over the lock assembly, waver the other end up and over the mounting stud.

Photo 11 shows the bowl in place, through the mounting slot over the mounting stud. The lock pawl is v the plate at the far end.

Photo 11a shows just how the plate fits ~ above the ago of the lock as soon as properly seated.

See more: How Many Pints Are In The Human Body ? How Many Pints Of Blood Does An Average Body Hold

You have the right to now placed the nut back on the handle mounting stud.

*
11

*
11a

Photo 12

The arrowhead in photo 12 points to the door jamb set screw. V the plate and also handle mounting nut already tightened in place, screw the set screw in until it makes good contact v the door jamb metal. Stop quick of the screw pointer piercing the door jamb metal, however if the does, just file the point off native the external door jamb.

Recheck the the lock pawl moves easily past the screw head and also doesn"t have any interference with the plate. (Minor rubbing that the rod versus the bowl is no a problem, just put a dab of grease whereby the rod touches the key if needed.)

If rod seems to rub as well much, the lock pawl have the right to be bending slightly far from the plate to get a small room. Host the lock pawl ~ above the lock through a tool or her finger prior to trying to bending the pawl so the clip doesn"t popular music off!

*
12

You are currently ready to put the door back together. Work in turning back order to put things back in place.: Make certain you don"t have any kind of leftover parts

Test the duty of her windows, locks and latch prior to doing the various other door.

Now you have the right to place the window warning brand in the lower edge of the window. Clean and also dry the window before putting the sticker on. Location carefully because the adhesive top top the sticker labels is very strong.